6 heat Reclaim / Radiator Fins 6 inch dia wood stove pipe flue stack exchanger

Description

This is a set of six ,
6 inch diameter stovepipe radiator rings that extract heat from the hot stove
pipe and radiate the heat into the room.  They will fit 6″
stovepipe.  See other listing for 3″, 3.6″, 4″, 5″, 7″, and 8″ pipes.  Installed, they make
close contact with your stove pipe and conduct more usable heat from the hot
pipe to be released into the room.  They, in effect, increase the surface
area of your stovepipe between the stove and the chimney, therefore allowing more
heat to be radiated and released into the room.  They work just like the fins on a motorcycle engine,
they increase the area of heat dissipation.
.
You get one lot of 6 radiators.   Made of 28 gauge high thermal conductivity aluminum,
1
½” wide.
W
ill work with any heat source.
Installed close together, this one set of 6 radiators will cover 9 inches of pipe.
The heat exchanger bands may be placed close together (no space between) to allow more bands and more heat extraction.  But make sure to offset the loops to allow air circulation in the loops. (information is included in the instruction sheet  provided)
They attach quickly and easily to your stovepipe.
…no screws or tools needed.  The ends lock into each other.
It takes
about 5 minutes to attach all six radiators.
The bands conduct heat from
the points of contact on the stovepipe to the loops in the band where the heat
is released into the room.
The band
loops get nearly as hot as the stovepipe…too hot to touch.
PLEASE,  PLEASE……MEASURE THE CIRCUMFERENCE OF YOUR PIPE (the length around) WITH A FLEXIBLE TAPE MEASURE !     Do not guess at your diameter…it is impossible to measure the diameter of an installed pipe.    ORDER BY CIRCUMFERENCE….see below.
FREE HEAT…
How much heat?  Here is an example for a 6″ dia. set.
Each
6” diameter radiator has 10 loops that are
2” x  1.5”…that is 30 square inches of sheet metal.
6 x 30 sq/in
= 180  square inches of sheet metal.
That is equivalent to a  12″ x 15” sheet of metal.
So in effect, by installing this
set of 6 bands, you create the equivalent of this 12″ x 15” sheet of hot sheet
metal, 300 – 500 degrees, radiating heat from
both sides
of the sheet
into the room before it escapes out the chimney.
That is like a small space heater itself…and it is
FREE
HEAT.
NOTE:  These will fit a
6″ diameter stovepipe…..See my other listing for radiators for 3″, 3.6″, 4″, 5″, 7″, and 8″
pipes.
They will last a lifetime.
They never need maintenance.
They may be re-used if you replace the old stovepipe.
They are guaranteed to draw more heat from the
stovepipe.
They pay for themselves in a short period of time.
You may put on as many bands as you wish or have
room for.
The more bands, the less heat
going out the chimney.
NOTE: The length of stovepipe in the picture is not
part of the sale… It was just for pictures to show the application.
Stovepipe Sizes
Approx.
Circumference
Diameter
Inches
(mm)
3”
dia  =                    9
1/2”                240
3.6”
dia.    =             11.3                 290
4”
dia  =                    12.6”               320
5”
dia  =                    15.7”               400
6”
dia  =                    19”                   480
7”
dia =                      22”                   560
8”
dia
=                     25                     640                           13
Note:
The bands are adjustable to fit the pipe
tightly.